URSSA P355 / P460. Steels fine grain for tankers

Steel resistant to temperature and pressure, applied pressure boilers, storage tanks, pipelines.

More details

Soldering:  Excellent
Folded:  Excellent
Transformation:  Excellent
Mechanization:  Excellent

General specifications*

C ≤ 0,20. Si ≤ 0,50/0,60. Mn 0,90-1,70. P ≤ 0,03. S 0,15-0,25. Al ≤ 0,020. Cr ≤ 0,30. Cu ≤ 0,30/0,70. Mo ≤ 0,10/0,08.
ReH315/355-400/460 N/mm2. Rm450/630-520/720 N/mm2. A 16/21 %

Characteristics

Steel plates specially manufactures for different kinds of welding structures..

Typical applications

Some of the applications could be: pressure boilers, moving tanks just as storage or parked, high pressure tubing, pole bridges, moorings, etc.

Supply status

Normalized

Welding/Soldering

Good: use always adequate systems for fine grain steels.

Folded

Good. Excellent folding characteristics in the sense of lamination.

Mechanisation

Good: it can be oxycuted, drilling and mechanised by any system.

Heat treatment

Some of the applications could be: pressure boilers, moving tanks just as storage or parked, high pressure tubing, pole bridges, moorings, etc.

Approximate equivalents

DIN:  TSTE 355 - TSTE 460
EH-36: A 572 Gr 65
BS: 22432A+B
AFNOR: A 52P1+2
A52-D: Fe E 355KT - Fe E 460 KT

Chemical composition (casting Análisis). According to EN 10028-3 (See rule).

Steel types% per mass
DesignationCSiMnPSAlCrCuMoNNbNiTiVNb+ Ti+V
SymbolicNumericMax.Max.Max.Max.Max.Max.Max.Max.Max.Max.Max.Max.Max.Max.Max.
P335 N1.05620,200,50,90 a 1,70,0300,0250,020,300,300,080,0200,050,500,030,100,12
P355 NH1.05650,200,50,90 a 1,70,0300,0250,020,300,300,080,0200,050,500,030,100,12
P355 NL11.05660,180,50,90 a 1,70,0300,0200,020,300,300,080,0200,050,500,030,100,12
P355 NL21.11060,180,50,90 a 1,70,0250,0150,020,300,300,080,0200,050,500,030,100,12
P460 N1.89050,200,61,00 a 1,700,0300,0250,020,300,700,100,0250,050,800,030,200,22
P460 NH1.89350,200,61,00 a 1,700,0300,0250,020,300,700,100,0250,050,800,030,200,22
P460 NL 11.89150,200,61,00 a 1,700,0300,0200,020,300,700,100,0250,050,800,030,200,22
P460 NL 21.89180,200,61,00 a 1,700,0250,0150,020,300,700,100,0250,050,800,030,200,22

Mechanical characteristics in room temperature. According EN 10028-3 (See rule)

Steel typeNormal supply status

Elastic limit ReH minimum
in N/mm2
For thickness product in mm

Resistant to tensile
Rm
in N/mm2
For thickness product in mm

Minimum Lengthening after break in % (Lo=5,65 VSo) Nominal thickness in mm

Designation
SymbolicNumeric≤ 16> 16 ≤ 35> 35 ≤ 50> 50
≤ 70
> 70 ≤ 100> 100
≤ 150
≤ 70> 70 ≤ 100> 100 ≤ 150≤ 70> 70 ≤ 150
P335 N1.0562Normalized (See rule)355355345325315295490 a 630470 a 610450 a 5902221
P355 NH1.0565Normalized (See rule)355355345325315295490 a 630470 a 610450 a 5902221
P355 NL11.0566Normalized (See rule)355355345325315295490 a 630470 a 610450 a 5902221
P355 NL21.1106Normalized (See rule)355355345325315295490 a 630470 a 610450 a 5902221
P460 N1.8905Normalized (See rule)460450440420400380570 a 720540 a 710520 a 6901716
P460 NH1.8935Normalized (See rule)460450440420400380570 a 720540 a 710520 a 6901716
P460 NL11.8915Normalized (See rule)460450440420400380570 a 720540 a 710520 a 6901716
P460 NL21.8918Normalized (See rule)460450440420400380570 a 720540 a 710520 a 6901716

Minimum values of the absorbed energy in the bending impact bending test.
Applicable to test tubes with notch in V, according to EN10028-3.

Steel typeSupply statusProduct Thickness

Minimum value of the energy to break in J
Longitudinal transversal testers determine the temperature in essay in ºC

-50-40-200+20-50-40-200+20
P …. NNormalized5 a 150 mm
P … NHNormalized5 a 150 mm404755202727
P … NL 1Normalized5 a 150 mm27344755631620273440
P … NL 2Normalized5 a 150 mm304065901002730406070

Elastic conventional limit at 0,2 % in high temperature. According to EN 10028-3

Steel typeProduct Thickness in mmConventional elastic limit at 0,2% in ºC (in N/mm2 mín.)
Symbolic designationNumerical designation50100150200250300350400
P 355 NH1.0565≤ 35336304284245226216196167
>35 a ≤ 70313294275245226216196167
>70 a ≤ 100300275255235216196177147
> 100 a ≤ 150280255235216196177157127
P 460 NH1.8935≤ 35402373333314294265235
>35 a ≤ 70392363333314294265235
>70 a ≤ 100373343324294275245216
> 100 a ≤ 150353324304275255226196

Stock Program

  • Large range of densities and formats from 3 to 20mm thickness. Check our stock in the warehouse for each supply, as if delivery period for formats not available.
  • We also serve parts of sheet, cut in multiples lengths of 1000mm maintaining the width.
  • Oxycut of tailor-made pieces from 6-8 mm thickness.

* The specifications are illustrative. For each supply we offer a certificate with the datum of the shipment delivered.

Ask for information

Ask us for more information and advice on URSSA P355 / P460. Steels fine grain for tankerss.

Request info

Download

Oxycut on demand

Oxycut on demand

We cut your steel plates starting from your plans with absolute accuracy. An added service which allows collecting the product ready to be used.

Send us your project now.


Special steel plates

Special steel plates

Wide stock in steel plates with a thickness ranging from 1.5mm to 400mm and different types. Ask us for more information.


steel sheet corten

Steel sheet corten

Wide range of thicknesses, from 1mm to 80mm thickness. Oxcut custom made from 8mm to more than 500mm thick